• fuckwit_mcbumcrumble@lemmy.dbzer0.com
    link
    fedilink
    arrow-up
    11
    ·
    6 months ago

    Soldering is easy if you have the right tools. Those old school solder irons with the ceramic element dangling inside a metal tube suck balls. Get yourself a direct heat iron like the pinecil and some flux and it’s SOOOOO much easier.

    • Omgpwnies@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      6 months ago

      It sounds like you’re talking about Weller style irons and the ones where the part you hold plugs directly into the wall are quite terrible. However, they are an industry standard and most soldering stations will use a Weller tip. I have a knock off Hakko 936 that’s like 15 years old now and cost me $25 and it solders like a dream.

      • fuckwit_mcbumcrumble@lemmy.dbzer0.com
        link
        fedilink
        English
        arrow-up
        2
        ·
        6 months ago

        I’m talking about all of the older style soldering irons, including like that Hakko. The Pinecil is $25 AND solders better. Once I switched to a direct heat iron I can never go back. The difference is HUGE.

        • Almrond@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          6 months ago

          They are closer to $40-60 after shipping, not $25. I have been using a $10 Weller for a lot of years, with proper technique I have never been able to notice a difference in my joints or difficulty in soldering. I prefer my Weller for some jobs because it simply has more thermal mass. Stuff like repairing the connections on a 3D printer hotbed would be impossible with a Pinecil.

    • Dieinahole@kbin.social
      link
      fedilink
      arrow-up
      2
      ·
      6 months ago

      I’ve had tools, teachers, and time.

      I can’t solder or braze to save my fucking life, but I’ll weld circles around you with oxy, stick, mig, or tig.

      Doesn’t make a damn bit of sense to me

      • jjagaimo@lemmy.ca
        link
        fedilink
        English
        arrow-up
        1
        ·
        edit-2
        6 months ago

        I felt the same the first time I tried but it honestly takes a few tries to start getting it right. The kind of iron and solder matter a lot; the older ceramic core ones suck and the JBC/pinecil type are much superior. Part of the problem with the ceramic type ones is they have one setting - full blast - and not good temperature control. With a pinecil/JBC you can set the temperature to 300C and expect to get 300C. Too hot and it will boil off the flux before you’re done soldering and you just get crud.

        In terms of solder, leaded rosin core solder is the best. Don’t worry about the lead, as long as you wash your hands. Use a brass sponge type thing to clean the tip frequently to remove crud

        For through holes, I’d say get some veroboard off eBay and a bunch of cheap resistors and just start plugging away until you get better. Process is basically - have tip with a bit of solder, poke to pad and pin, put solder into joint and hold 1-3 seconds until solder flows onto pad and pin, remove tip. Putting some flux on in advance helps remove the oxides before soldering

        For surface mount (side pads/pins), there are kits with cheap/obsolete/trash components you can just plug away at without fear of messing anything up. Soldering smt is a bit annoying but doable by hand without much training. the process is basically: tin one pad, use tweezers to place part and reheat the solder until the part is in place, solder the rest of the pads, reheat first pad to relieve stress.

        Even for large parts, I used to have trouble with unsteady hands. If you are doing smt you really need a microscope or magnifying glass for anything smaller than 0805 - really helps with the visual feedback loop for hand positioning. A microscope significantly improved my dexterity and hand steadiness